A Proactive Rant About Car Key Button Repair
Car Key Button Repair
A broken car key can be a hassle. It is possible to call the 24 hour Locksmith Service or purchase an alternative remote.
You may be able save money by fixing your old key fob instead of replacing it. This is particularly true if a worn-out switch or faulty contacts are the cause of the issue.
Battery
If the buttons on your key fob don't respond to pressing, this could be a clear indication that the battery is dead or nearing the end of its lifespan. Fortunately replacing the battery is a simple task that you can complete on your own rather than hiring a locksmith to do it for you.
Locate the battery compartment first. car remote key repair near me is typically located on the back of the key fob and is often concealed behind a cover that opens or a button that opens the access point. Once the compartment has been exposed then look for the small button-cell battery. It is usually shaped like an ordinary coin and is marked with an plus and minus symbol. Remove the battery from the old one and replace it with a new one in its place, making sure that the plus and minus marks are aligned correctly.
Once the battery is installed, close the compartment and snap the two parts of the key fob together. Before closing the door, align and snap the components into place. To ensure that the buttons work properly Press any of them.
If the remote keyfob does not work after replacing the battery, there may be other problems that require a different kind of repair. Damage to the physical structure caused by dropping the fob into a puddle, for example, can sometimes cause it to stop functioning altogether. It could also be due to a malfunction with the internal electrical system or the need to be deprogrammed. Check out these other common car troubleshooting tips to see whether your key fob may be experiencing a different issue.
Switches
Depending on the year and manufacturer, there are various kinds of switches that are found in the car keyfob. The older type of key often has a separate chip that you can see in the case, whereas newer keys are more advanced and operate by sending signals to the car. Regardless of the type of key, the keys' buttons can get worn down or damaged when used regularly. The result is they become difficult to press or even ineffective. If you attempt to force the button to work, it can cause further damage, and could even prevent the key from being able to start your vehicle in the future.
If your key doesn't seem to be working, you should first try changing the battery. If this doesn't work, then you might need to clean your key fob or adjust its switches. Because these tiny electronic switches spend a lot of time getting jostled around and tangled, they are more likely to break down than the larger components of your key.
The switches feel rubbery and are coated with an electrical conductor. The film may fade over time. Fortunately, they are also tiny and affordable to replace. The old ones are soldered onto the circuit board, so you will need to carefully remove them without damaging anything else. You can then solder new ones into and then reassemble your fob.
An effective way to protect your car key fob from being ruined is to avoid using it for more than a few hours at a stretch, and also to not leave it in places where it can be seen. If you don't use your key, keep it in a safe place.
If you've tried cleaning your key fob and replacing the battery, and the issue persists it's probably time to think about hiring a locksmith. A professional can check the frequency of your key to determine if it's still able to communicate with your vehicle, open and replace micro switches, alter cases, and more.
Outer Case
If the buttons can't move freely in the case, they could be stuck or even break. If cleaning the case using rubbing alcohol and a cotton swab doesn't work, it could be necessary to take off the case. If the contacts the buttons touch aren't an ideal fit or if they're damaged, adjusting them could be the only option.
Rubber buttons may be worn out over time. Rubber buttons can become hard to press because they stretch, and nails may gouge them. This could cause the key to fail and in this instance it's time to get an entirely new case or buttons. This repair involves removing the remote, then locating the buttons on the circuit board, and then heating the solder and carefully removing them. The circuit board is then soldered with new buttons. The case can be reassembled, and the horseshoe key blade can be attached. The new buttons should be securely fitted inside the case to prevent them from falling out.
Inner Case
Since your key fob is likely to be tossed around and sometimes be accidentally pressed and the buttons within can get damaged or stuck over time. Utilizing metal tape and a hole-punch, you can usually fix this problem when your car is away from home when the key fob won't work, allowing you to unlock the doors, but not start the engine. This simple fix will enable you to safely get back to your vehicle and continue your journey.