20 Things You Should Be Educated About Car Key Button Repair
Car Key Button Repair
A damaged car key button is frustrating. You may need to call a 24-hour locksmith Service for help or purchase a new remote.
You could be able to save money by fixing your old key fob instead of replacing it. This is particularly true if the problem is due to the worn-out switch or defective contact.
Battery
If your key fob's buttons do not respond when you pressing them, it could be a sign that the battery has died or is about to reach the end of life. Fortunately replacing the battery is a simple task that can be completed by yourself rather than hiring a locksmith to take care of it.
Find the battery compartment first. The battery compartment is typically located on the back of the key fob and is often hidden behind a cover which slides out or an open button that opens the access point. When the compartment is open you can see the small button cell battery. It's usually shaped as an oblong coin and is identified with an minus and plus sign. Take the old battery out and replace it with a new one. Check that the plus and minus symbols are aligned correctly.
Once the battery is in place, close the compartment and snap the two halves of the key fob together. Before closing the door, align and snap the components into the correct position. Press any of the buttons to ensure that they work properly.
If your remote key fob stops functioning even after replacing the battery, it could be suffering from other issues that require a different kind of repair. Dropping the device in a puddle could cause it to cease functioning. Alternatively, it might be experiencing an internal electrical problem or may need to be deprogrammed by a dealer or locksmith. See if you can find out if the problem is with your key fob by using these other methods for troubleshooting your car.
Switches
There are a variety of switches that are used in the car key fob dependent on the year and make. The older style key has an embedded chip that can be seen in the case. The latest keys operate by transmitting signals to your car. The keys' buttons can be damaged or worn out through regular use, irrespective of the type. They become hard to press or unresponsive. If you force the button, it could cause further damage. It may also prevent the key from functioning in the future.
If you're unable to get your key to function Try changing the batteries. If that doesn't help, you may need to clean the key's fob and re-adjust the switches. Because these tiny electronic switches spend a lot of time being tossed around they are more prone to wear out than larger components of your key.
The switches are rubber-like and are coated with an electrically conducting film that wears down over time. Fortunately, they are also small and affordable to replace. They are soldered onto the circuit board, which means it is important to remove the old ones without causing any damage to anything else. You can then solder the new ones into and then reassemble your fob.
An effective way to protect your car key fob from becoming ruined is to avoid using it for more than a few hours at a time and to keep it out of the way in places in areas where it is visible. Also, make sure car key repair company find a secure location to store your keys when you're not using it.
If the issue persists after you have cleaned your key fob, replaced the battery and attempted to clean it, you may need to consult a locksmith. A professional can check the frequency of your key to determine if it's still able to communicate with your vehicle, and open and replace micro switches, change cases and more.
Outer Case
If the buttons can't move freely up and down the case, they may be stuck or even break. If changing the battery or cleaning with an alcohol-based swab and a cotton pad alcohol rubbing doesn't solve the issue, then removing the case and inspecting might be necessary. If the contacts that the buttons touch are not suitable for the application or are worn, changing them might be the only option.
Rubber buttons get worn out over time. Rubber buttons can become difficult to press as they stretch, and nails may gouge them. In this situation the key could fail and it's time replace the case or buttons. This repair involves disassembling the remote, finding the buttons on the circuit board, and then heating the solder and carefully removing them. New buttons are then soldered to the circuit board. The case is then put back together with the horseshoe key blade piece is attached. The new buttons must be snugly fitted into the case to prevent them falling out.
Inner Case
Since your key fob is likely to be tossed around and could occasionally be pressed by accident, the buttons inside can be damaged or stuck over time. Using metallic tape and a hole-punch, you can often quickly fix this problem when your car is away from home when the key fob won't work and allows you to open the doors, but not to start the engine. This simple fix can enable you to safely get back to your car and continue your journey.